Why a written comparison beats a sales call
When you buy a mobile steam cleaning machine, the machine itself is only part of the cost. A unit that cannot be driven through your parking deck, refilled from a normal tap, or run on the battery pack you already own will pull your team onto downtime you did not budget for. Putting every candidate on the same sheet of paper, before the first call, is how procurement teams avoid that trap.
The comparison sheet below follows the same field order used in the PowerDe cleaning equipment specifications, so numbers collected from different suppliers can be read side by side without translating one vendor's wording into another's.
1. Mobility and footprint
Start with how the machine reaches the vehicle. PowerDe's driving-style models — PWD01, PWD02 and HMW2 — are self-propelled units listed with autonomous driving, at L1275 mm × W570 mm × H1185 mm. Height is the number most often missed: a machine that fits a service lane in width can still be stopped by a mezzanine, a pipe rack, or a low garage door.
Compare that with a hand-pushed unit such as the PowerDe HMW3, listed at L1150 mm × W520 mm × H1030 mm. It is shorter and narrower, and an operator moves it instead of a drive motor, so the trade is labour for clearance. In your table, record the tightest width and height on your site, then write each machine's figures next to them.
- Mode of movement: autonomous driving or hand push — and who supplies the power for each variant
- Length, width and height as listed, plus turning clearance in your layout
- Whether the machine can be stopped and driven again during a job without a shutdown cycle
2. Cleaning modes: dry steam, wet steam, hot water
The mobile active-water line offers three modes: hot water, dry steam and wet steam. In a PowerDe PWD02 steam cleaner, that combination covers rinsing loose road film with hot water, lifting packed grease with wet steam, and finishing with dry steam when the surface should leave the bay already dry. A hand-pushed model such as the HMW3 is listed with dry steam and wet steam only, so a hot-water pre-rinse drops out of the workflow.
Write down which modes you will use on a normal shift before paying for modes you will not. If your workload is interior and engine-bay work, dry steam matters more than tank volume. If you wash exterior surfaces daily, the hot-water mode and the high-pressure water gun carry the job.
3. Power source and battery supply
This is where two models with the same name behave differently. The PWD02 page lists 220 V working voltage with a replaceable 455 V mobile battery. The HMW2 is listed at 48 V mobile battery and states that batteries are customer provided. The HMW3 runs from a 48 V battery. One catalogue can therefore ship a machine you plug into shop power, a machine you supply a battery for, and a machine with a mobile pack.
In the comparison, list the working voltage, whether the battery is inside the quoted price, and whether that battery platform and its charger are already on your shelf. A price that looks lower because the battery is excluded only makes sense if your fleet already carries a compatible pack.
4. Heating, tank and water supply
The mobile PWD02 and HMW2 are specified with 4.5 kW semiconductor heating and a 60 L clean water tank; the hand-pushed HMW3 uses the same 4.5 kW semiconductor heating with a 50 L clean water tank. All three take tap water through a 4-point internal-tooth joint, so a normal site tap feeds them without a special water treatment line.
Use tank volume to work out how often the operator stops to refill, and heating power to understand the wait before the first lance of steam. On a fixed point the numbers change again: the PowerDe HW02 is listed at 6 kW heating power with an 80 L stainless steel tank, which suits a permanent wash position rather than a unit you drive between bays.
5. Safety design and protection features
PowerDe's cleaning equipment pages describe leakage protection, short-circuit protection, high-temperature protection, high-voltage protection, water-shortage protection and high-voltage explosion protection. Compare the list rather than a count, because suppliers group these differently, and the wording on the datasheet is what you can hold a supplier to at commissioning.
Ask each supplier which protection stops the machine, what the operator sees when it stops, and how the unit is reset. Water-shortage protection in particular decides whether an empty tank becomes a burnt heater or simply a stop.
6. Throughput and the real cost per wash
Do not compare machines on a single washes-per-hour claim. Compare the elements that produce that number: the cleaning method (the mobile models use a high-pressure water gun with nozzle), the vacuum option, tank size, and the distance between wash point and water point. Where a vacuum is offered, the listing describes a vacuum cleaner with a flat nozzle feeding a sewage tank, which matters if interiors are part of the job.
Fill in, for each candidate: operator minutes per vehicle, refills per shift, and how many machines your layout can run at once. Multiply by the wages you actually pay. That figure, not the sticker price, is what the comparison should decide.
7. Total cost of ownership and service
Add the items that appear after the invoice: battery purchase or replacement, consumable nozzles and hoses, and lead time for the heater and control parts. A driving-style machine with a replaceable battery pack is cheaper to keep running when your team already maintains those packs; a fixed 220 V unit is easier to plan around when power is guaranteed at the wash point.
Ask the manufacturer named on the datasheet — Shenzhen PowerDe Automation Precision Equipment Co., Ltd, Shenzhen — which parts it stocks for the model you shortlist, and what it supplies for the variant you order. Battery-included and battery-excluded variants of one model can carry different service paths.
8. Customisation and supplier support
If no catalogue model fits your layout, PowerDe lists engineering services around its cleaning line, including customized steam cleaning equipment and steam cleaning equipment product development. Bring your measurement sheet, your vehicle mix and your site's tightest clearance into that conversation; a specification built from your data is a cheaper brief than a standard model you later have to work around.
A comparison table you can hand to every supplier
| Field | Why it belongs in the sheet | PowerDe reference on the listing |
|---|---|---|
| Mode of movement | Decides whether the machine drives itself or is pushed to the bay | autonomous driving (PWD01, PWD02, HMW2); hand push (HMW3) |
| Machine dimensions | Must clear doors, racks and lanes on your site | L1275×W570×H1185 mm; HMW3 L1150×W520×H1030 mm |
| Cleaning modes | Defines which tasks the machine can do at all | hot water, dry steam, wet steam; dry steam and wet steam on HMW3 |
| Working voltage and battery | Shows whether the quote must include a battery pack | 220 V with replaceable 455 V mobile battery; 48 V mobile battery, customer provided |
| Heating power and heater type | Sets heat-up time and steady steam supply | 4.5 kW semiconductor heating; 6 kW on fixed HW02 |
| Clean water tank | Sets refill frequency during a shift | 60 L; 50 L on HMW3; 80 L stainless steel on HW02 |
| Water inlet | Confirms the machine runs from a normal site tap | tap water inflow, 4-point internal-tooth joint |
| Cleaning method | The tool the operator holds for most of the job | high pressure water gun with nozzle |
| Vacuum option | Needed when interiors are part of the wash | vacuum cleaner with flat nozzle, sewage tank |
| Protections listed | What the supplier is accountable for at commissioning | leakage, short circuit, high temperature, high voltage, water shortage, high-voltage explosion protection |
Questions to put in writing before you order
- For the exact model and variant you are quoting: is the battery included, and at what voltage?
- What is the machine's total height including handles and mounted accessories, against my site's lowest obstruction?
- Which of the listed cleaning modes are standard on this variant, and which are options?
- What is the lead time, and what is the spare-parts route for the heater, gun, hose and nozzle on this variant?
- Can the tank be refilled from my existing tap without an adapter, and what fitting is supplied?
- If my layout needs a change to the standard configuration, what is the engineering path and the cost of that change?
Work through those fields with every shortlisted machine, and the comparison stops being a contest of opinions. If you want a configuration built around your own measurements and vehicle mix, the cleaning equipment team can be reached through the contact page on powerde.net.
