A fixed steam cleaning machine stays in one place, connected to permanent power and water, and cleans whatever passes through its bay or work area. Because it is built around a permanent installation rather than a battery and a hose reel, the configuration that works well depends heavily on how and where it will be used. Before requesting a machine, gather the details below. Sharing them at the start lets the manufacturer recommend the right configuration, and it helps you avoid paying for a machine that does not fit the job.
1. What is being cleaned, and what has to be removed
Describe the target and the soil in plain terms. Steam cleaning covers a wide range of jobs, and the cleaning target determines the mode selection, the accessories, and whether a fixed unit is the right form factor at all.
- The surface or object: vehicle exteriors, engine compartments, interiors, kitchen hoods, machinery, or equipment frames.
- The soil: road grime, oil and grease, food residue, dust, or a combination.
- Whether the job is routine cleaning, heavy grease removal, or cleaning with a disinfection requirement.
The fixed steam cleaning machine PowerDe HW02, for example, is listed for vehicle exterior cleaning at gas stations and parking lots, interior vacuuming and disinfection, and engine-compartment cleaning. If your application falls outside the uses published for a model, say so in the request and ask the manufacturer to confirm suitability rather than assuming it.
2. What the installation site can supply
A fixed machine is only as good as the utilities beside it. Include these details with your request:
- Power: the available voltage and whether a dedicated circuit can be run. The HW02 operates on a 220 V supply and lists 6 kW of heating power, so the circuit and protection devices must match.
- Water: whether a tap-water inlet is available at the position. The HW02 uses a 4-point internal-tooth fitting, and the connection size should be confirmed before installation.
- Drainage and floor slope: steam cleaning produces hot water and loosened soil on the floor, and a drain or a way to collect it should be planned in.
- Space: the machine footprint, plus clearance for the operator and the hose. The HW02 is listed at 1,200 × 800 × 1,200 mm including handles; measure your bay against that before ordering.
- Environment: indoor or outdoor, covered or exposed, and the temperature range in winter if the machine is installed somewhere unheated.
3. Whether a fixed unit is the right form
Tell the manufacturer how the work actually moves through your site. A fixed unit suits a dedicated bay where vehicles or objects come to the cleaning position. If cleaning has to follow the vehicles, or if bays and utilities are shared, a mobile machine may be the better answer. PowerDe's cleaning equipment series covers both forms: driving-style and hand-pushed machines for positions without fixed utilities, and fixed machines for permanent positions. Describing your layout — the number of bays, the distance between them, and where power and water exist — lets the manufacturer steer you to the correct form instead of quoting whatever you happened to ask for.
4. Duty cycle and workflow
Describe a normal working day, not a worst case:
- How many vehicles or objects are cleaned per day, and over how many shifts.
- Whether cleaning runs continuously or in bursts, and how long the machine must run between breaks.
- Who operates the machine, and whether more than one person will share it.
These details drive the tank size, the heating power, and how much recovery time the machine needs between jobs. The HW02 carries an 80 L stainless steel (SUS304) tank and produces steam at a listed 160° with a vapor pressure of 0.8 MPa; whether that capacity fits your day depends entirely on the numbers you provide.
5. Mode selection and special requirements
State what the machine must do beyond removing soil:
- Which modes you expect to use. The HW02 switches between dry and wet steam and includes a vacuum cleaner for interior work; dry steam suits light soil and surfaces that should not be soaked, while wet steam suits heavier deposits.
- Whether disinfection is required, as it commonly is for vehicle interiors, medical environments, and food areas.
- Whether chemical detergents are restricted or not allowed at all.
- Any safety requirements for the site. The HW02 page lists leakage, short-circuit, high-temperature, high-voltage, water-shortage, and high-voltage-explosion protection; if your site has additional rules, include them in the request.
A request you can copy
A complete request reads something like this:
- Target and soil: cars and light vans, exterior road grime, occasional engine-compartment cleaning.
- Site: covered bay, 220 V supply available, tap-water inlet and floor drain in position.
- Duty: 30 vehicles per day across two shifts, one operator.
- Requirements: dry and wet steam, interior vacuuming, no chemical detergents.
With those details in hand, a manufacturer can confirm whether a fixed machine fits, which model to look at, and what accessories to include.
Send the details, get the configuration
The purpose of sharing application details is not paperwork. It is how a manufacturer matches a machine to your site, your workflow, and your constraints — and how you avoid buying a fixed unit when the job actually needs a mobile one. If you are specifying a fixed steam cleaning machine for a vehicle bay, a workshop, or a facility with permanent utilities, send the cleaning target, the site conditions, the daily workload, and the special requirements together. PowerDe offers customized steam cleaning equipment, so the same information is what turns a general inquiry into a specific, usable configuration.
