Installation requirements get decided by applications, not by the machine. A fixed unit in a wash bay, a hand-pushed unit moving down a ward corridor, and a driving-style unit working through a narrow parking area all need different power, water, drainage, access and storage arrangements. So the honest way to plan an installation is to read the applications the product page actually names for the model you are installing, and derive the site work from those — not from a generic "steam cleaner installation" checklist.
Read the application list on the model's own page
Each cleaning model's product page states what it is positioned for. The fixed PowerDe HW02 steam cleaner page lists vehicle exterior cleaning at fuelling stations and parking areas, interior vacuuming and disinfection work, and engine-compartment cleaning. Those four applications already dictate the installation: a hard standing area with room to work around a vehicle, a 220 V supply at the station, a tap-water connection, somewhere for the runoff to be contained and collected, and storage for the machine beside the bay rather than across the yard. A dry and wet steam cleaner such as the PWD02 is listed for indoor garages and narrow outdoor parking spaces, which shifts the site work towards access, doorway widths and a charging or standby arrangement instead of a fixed water inlet.
The rule is simple: the application list is the requirements list in disguise. Every named application implies one or more site conditions, and the ones that imply nothing are usually the ones that go wrong at commissioning.
Derive the utility requirements from the parameter table
Read the published parameters as site constraints, one by one, and write your own condition next to each figure:
- Working voltage — the HW02 lists 220 V with 6 kW heating power; a hand-pushed medical equipment steam cleaning unit such as the HMW3 lists a 4.5 kW PTC heater on a 48 V battery supply. Mains units need a circuit at the working position, with the cable run planned rather than improvised. Battery units need a charging point, a charge routine and a runtime verified against a full shift.
- Water inlet — the HW02 lists a tap-water inlet with a 4-point internal-tooth joint. That is a plumbing connection at the station, with the fitting confirmed before installation, not a hose into a bucket.
- Tank capacity — 80 L SUS304 on the fixed unit, 50 L clean water on the hand-pushed unit. Capacity plus heating power decides how long the crew can work before a refill or a recovery period, which decides whether one machine covers a shift.
- Footprint — the HW02 is listed at roughly 1200 × 800 × 1200 mm including handles, and the HMW3 at about 1150 × 520 × 1030 mm. Put those numbers against your actual doorways, corridors, lifts and thresholds, including the frame, not the drawing.
- Steam output — 160°C and 0.8 MPa with a dry/wet switch means ventilation, a wet floor, and a working area where people cannot walk into a wand.
Plan for the residue the applications generate
Each named application produces its own waste stream: degreased water from engine work, grease-laden runoff from vehicle exteriors, and dirty water from interior cleaning. Installation is the moment to decide where that water is collected and how it leaves the site, because surface drainage is not a disposal route and a drain that was not planned becomes a channel cut later at far higher cost.
Install for the protections you were sold
The HW02 page lists leakage, short-circuit, high-temperature, high-voltage, water-shortage and high-voltage-explosion protection. Those features assume an installation that matches them: a correctly protected circuit, an adequate earth, a water supply that will not run the unit dry, and a machine standing that will not move under hose pull. Confirm the site conditions against the protection list during installation, and record what was checked, because that record is what a safety review asks for.
Do not read one model's applications across the range
This is where installation briefs go wrong. Application wording on one product page is not a licence to install the same way elsewhere. PowerDe's own site carries inconsistencies between product titles and overview text on some cleaning models, so before any installation is committed, check the figures and the named applications against the specific model's detail page, and ask the supplier to confirm in writing when your intended use is not named there. Kitchen degreasing, machine-tool cleaning, agricultural and medical duties appear in the customer's marketing directions, but that is a direction to develop, not an installation specification.
Close the installation with a documented commissioning check
Finish with one page: model and serial, the published parameters you installed against, the utilities verified at the working position, the access route measured and demonstrated, the runoff collection route, the protection checks performed, and the named applications you intend to use the machine for. Keep it with the manual and the training record. If that page shows your applications do not fit the standard configuration — no water inlet where the work happens, an access route the machine will not pass, a duty the model's page does not list — PowerDe works on customised steam cleaning equipment, and that commissioning page is the document to send with the enquiry.
