A fixed steam cleaning machine is not a shelf item you can order off a catalogue number and expect to drop straight into a service bay, a fleet depot or a plant maintenance corner. PowerDe's fixed steam cleaning machine line is built on a common platform, but the water supply, power supply, shift pattern and the surfaces being cleaned all shape which configuration actually works. A configuration review is how we settle those questions before an order is placed. Here is the practical process, and exactly what to send us so the review turns around quickly.
Why a fixed unit first, before any review
Fixed machines sit on a station and run from mains power and a water inlet, so they suit a permanent washing position: a service pit, a fuelling station bay, a workshop corner where machinery is cleaned on a schedule. The PowerDe HW02 steam cleaner is the reference model in this group — 220 V, 6 kW heating power, steam at 160°, 0.8 MPa vapour pressure and an 80 L SUS304 tank, with dry steam and wet steam modes plus a vacuum function. Its footprint is 1,200 × 800 × 1,200 mm including handles, which is a real constraint in a narrow bay and one of the first items we check against your floor layout.
If your work moves between bays or your site has no water point where the machine has to stand, a mobile unit from the PowerDe cleaning equipment range may be the better starting point. The review will tell you honestly which of the two your site points to — that is the whole reason to do it before purchasing rather than after.
What we need from you in the first message
A configuration review is only as fast as the information behind it. Six items are enough to produce a working proposal, and each one changes a specific decision:
- Site power. Supply voltage, phase, and the rating of the available breaker. A 6 kW heater on a 220 V circuit needs a dedicated circuit; a shared one will trip under load and stall a shift.
- Water source. Whether a tap can reach the machine, and with which fitting. The HW02 is fed with tap water through a 4-point internal-tooth joint, 1/2 inch. No water point means either relocating the machine or going mobile.
- What gets cleaned. Vehicle exteriors, engine compartments, machinery housings, floors, walls. Grease, cutting oil and road grime respond differently to dry steam and wet steam, and this drives the mode mix and the accessory set.
- Duty pattern. How many units or machines per shift, how many cleaning sessions per day, and how long each session runs. This is what tells you whether the 80 L tank and one machine are sufficient, or whether a second unit and a duty rotation are cheaper than waiting.
- Floor space and access. Bay dimensions, door widths and the route from the water point to the machine position. Compare these against the machine's working dimensions before anything else.
- Constraints that are non-negotiable. Drainage arrangements, wet-floor and slip rules, shutdown windows, any requirement to avoid detergents on a surface.
Photographs of the bay or the equipment being cleaned, and a rough layout sketch with measurements, shorten the review considerably. A single wide photo of the working position usually answers two or three questions at once.
How the review is carried out
The review runs in four steps, and you get a written answer at each one rather than a single quote at the end.
Step 1 — feasibility check. We confirm that a fixed machine can be installed where you intend to use it, and that your power and water can support it. Where they cannot, we say so at this stage and propose the alternative instead of shipping something that will sit idle.
Step 2 — duty sizing. Your session counts and shift pattern are matched against machine capacity, including heating-up time between sessions. This is where an under-sized single machine becomes visible: a fleet depot washing several vehicles back to back has a different requirement from a workshop degreasing one machine per week.
Step 3 — method and accessories. We set the dry-steam and wet-steam balance for your soils, then specify the nozzles and tools for the surfaces in question. Engine-compartment work, for instance, is handled as a separate task from bodywork in the engine compartment steam cleaning specification on the product page.
Step 4 — safety and operating assumptions. The HW02 platform carries leakage, short-circuit, high-temperature, high-voltage, water-shortage and high-voltage-explosion protection. The review records the site-side conditions those protections assume — earthing, water supply, operator training — so nothing is discovered on the first working day.
What you receive at the end
A completed review delivers a defined machine configuration, the accessory list, the installation preconditions written as an installable checklist, and a quotation for that specific build. If a fixed unit is not the right answer for your site, the review says so and points to the mobile alternative. Nothing is ordered until you confirm the configuration.
If you are evaluating equipment for more than one site, send the layout and power details for each location in one enquiry. Sites with a common duty pattern can often share a specification, while one awkward bay may need a different machine — which is exactly the difference a review catches early.
Frequently asked questions
Does the review cost anything? No. It is a pre-sales engineering step, and many buyers use it to compare options across suppliers before committing a budget line.
Can the machine be customised after the review? Yes. PowerDe builds customised configurations, and the review is where your requirement is turned into a defined build rather than a standard catalogue order.
What if my site has no three-phase supply? Send the supply details you actually have. Voltage and breaker rating are the first inputs in the review; a 220 V fixed unit must be matched to a circuit that can carry its heater load, and if it cannot, that finding belongs in the report, not in a callback six weeks later.
How do I start? Email sales@powerde.net or call +86 13023198376 with the six inputs above, and the review is returned as a written configuration proposal for your confirmation.
